The article author is making several great pointers about Tools You Need to Install a New Bathtub overall in this post directly below.
Mounting a tub isn't exactly brain surgery, however it does require solid plumbing, carpentry, and also in some cases, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately tough job. If the old bathtub is easily accessible, the job can relocate immediately; if you have to open up a wall surface to eliminate the old tub and also position the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to leave the old tub as well as set in the brand-new one. Make sure you have actually certified yourself for the work as well as fit attempting it. As opposed to hiring a specialist to take over a halfway-completed job, it is better to think about employing one before you start. Chances are you might need an expert plumber to make tube links.
This article will certainly aid you install a brand-new bathtub in your restroom if you have actually currently purchased a brand-new tub as well as do not need to alter the setup of your previous water supply pipelines.
Your devices and material list should make up the following:
Preparing for the Setup
To start with, the sustaining frame provided with the bathroom should be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to stop strain on the bathtub.
Fit the versatile tap ports to the bottom of both faucets making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now prepare to be suited its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, switch on the faucets to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have actually been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before going on to fit the new taps, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Utilizing both wood boards under its feet, place the bath tub in the required placement. The wooden boards are helpful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the tub until the level reads degree.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Turn on the water and examine all joints and brand-new pipework for leaks and tighten them if needed. Load the tub as well as also inspect the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the bath tub should wait up until the bath tub has been utilized at the very least once as this will resolve it right into its final setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washers remain in area in between the faucet as well as the sink. Safeguard the faucet in place with the manufacturer offered backnut. When the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet ports. The previous kind needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a rigid seal, causing the water to penetrate the wall between the bathroom and also the tiling, bring about difficulties with wetness as well as feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components and also installations. They are offered in tubes and cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the tub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealer can fracture rather early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently offered on the market. It is a good idea to fit the tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very curious about How to Install a Bathtub and I'm hoping you enjoyed the entire page. Those who enjoyed reading our post plz make sure you remember to pass it around. Thank you for your time. Please pay a visit to our website back soon.
Find Out More